ECX Circuit Instrukcja Obsługi Pobierz pdf (Strona 4)

COMPONENTS

VEHICLE PREPARATIONS

CHARGING THE VEHICLE BATTERY

1. Connect the AC power cord to the power slot on the charger, then

connect the other end of the power cord to an AC power source.

2. The Power LED and Charging LED will turn GREEN when the

charger is connected to the AC power source.

3.Connectthebatterypackconnectortothechargeconnector.

4.PresstheOn/Offbuttontochargethebattery.TheChargingLED

turns RED.

5. When the battery pack is fully charged, the Charging LED will turn

GREEN.

6.PresstheOn/Offbuttontostopcharging.Disconnectthebattery

pack connector from the charge connector.

CAUTION: If at any time during the charge process the

battery pack(s) becomes hot to the touch, unplug the

battery immediately and discontinue the charge process.

The vehicle battery charger produces 2000 milliAmps (2 Amps) per

hour. Divide the mAh capacity on the label of a battery by 2000 to know

howlongbatterychargingwillrequire.Forexample,afully

discharged 2400mAh battery requires 1.2 hours (72 minutes) to charge.

INITIAL CHARGE

Your Dynamite peak voltage detection charger includes safety circuitry

and programming. The charger will stop charging after 15 minutes if it

senses any issues that have come up in charging. The high electrical

resistance commonly found in new, unconditioned, Ni-MH batteries

can cause this safety circuit to turn off the charger before a full

charging cycle is complete. This is commonly known as a “false peak”

in your battery charge.

Shouldthisoccurduringyourrstchargecycle,itdoesnotnecessarily

indicate a failure of either your charger or battery. Instead, it shows

that the charger is functioning properly and that the battery is not yet

fully conditioned.

Tocompleteyourrstfullchargingcycleintheeventofafalsepeak,

restart the charger by pressing the Start button again. Repeat this

process until the charge cycle continues to charge past 15 minutes.

Itmaytakeasmanyas2to4restartstocompleteyourrstoneor

twofullchargecycles.Onceyourchargercompletesachargecycle

longer than 15 minutes, your battery will be fully charged. A typical

rstfullchargecycleshouldrunfor45to90minutes,dependingonthe

self-discharge condition of the battery since it was shipped from the

factory.

Onceyourbatteryisproperlyconditionedthroughafewfullcharge

and discharge cycles, you will see normal operation of the charger by a

single press of the start button, followed by a 60- to 90- minute charge

cycle.

CHARGING WARNINGS

WARNING:Failuretoexercisecautionwhileusingthis

product and comply with the following warnings could result

inproductmalfunction,electricalissues,excessiveheat,FIRE,and

ultimately injury and property damage.

• Readallsafetyprecautionsandliteraturepriortouseofthis

product.

• Neverleavethebatteryandchargerunattendedduringuse.

• Neverallowchildrenunder14yearsofagetochargebattery

packs.

• Neverattempttochargedeadordamagedbatteries.

• Neverchargeabatteryifthecablehasbeenpinchedorshorted.

• Neverallowbatteriesorchargertocomeintocontactwith

moisture at any time.

• Neverchargebatteriesinextremelyhotorcoldplaces

(recommended between 50–80°F (10–26°C)) or place in direct

sunlight.

• AlwaysuseonlyNi-MHrechargeablebatteries.Thischarger

cannot charge batteries such as “heavy duty”, “alkaline”,

“mercury” or “lithium” battery.

• Alwaysconnecttothechargercorrectly.

• Alwaysdisconnectthebatteryandchargerafterchargingandlet

them cool between charges.

• Alwaysinspectthebatterybeforecharging.

• AlwaysterminateallprocessesandcontactHorizonHobbyifthe

product malfunctions.

• Alwaysmakesureyouknowthespecificationsofthebatteryto

be charged or discharged to ensure it meets the requirements of

this charger.

• Alwaysconstantlymonitorthetemperatureofthebatterypack

while charging.

• Alwaysendthechargingprocessifthechargerorbattery

becomes hot to the touch or starts to change form during the

charge process.

• Alwayschargeinawellventilatedarea.

1. ECX

Circuit

™

1/10-scale 4WD Stadium Truck

2. Spektrum

™

DX2E Transmitter

3.AA(4)Batteries

4.DYN41132APeakBatteryCharger

5. Dynamite

Speedpack

™

7.2V

Ni-MH battery (DYN1060EC)

1 2 3 4 5 6 7 8 9 ... 13 14

Komentarze do niniejszej Instrukcji

Brak uwag

ECX Circuit Instrukcja Obsługi Strona 4

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Zabawki zdalnie sterowane ECX Circuit